Optimised Foundations for UK Commercial Solar
Geotechnical investigation, in situ validation and foundation design focused exclusively on commercial ground mounted solar projects in the UK. When steel quantities matter and installation risk is real, soil data must translate into buildable structural decisions.

We Don't Do Roads.
We Don't Do Housing.
We Do Solar.

Share the knowledge, manage the risk
Dayla Geotechnical is a specialist consultancy focused exclusively on commercial solar.
Dayla Geotechnical is a specialist consultancy focused exclusively on commercial solar.That focus matters.Solar foundations are repetitive, steel driven and cost sensitive. Small inefficiencies scale rapidly across thousands of piles.
This is not general ground investigation.
This is solar specific foundation intelligence.
Where Soil Data Meets Structural Reality
Many geotechnical reports are technically correct. Few are commercially useful.
Solar projects require more than soil logs and laboratory data. They require interpretation that informs structural design, steel quantities and installation strategy.
Dayla operates at the interface between ground behaviour and steel performance.
We do not produce reports for compliance alone.
We produce parameters that inform decisions.


Our Capability
Three disciplines that work as one
Site Investigation
Geotechnical, hydrological and topographical assessment interpreted specifically for solar foundation performance.
Validation and Testing
Solar pile pull out testing designed to reduce uncertainty and prevent refusal.
Design and Optimisation
Foundation design informed by soil behaviour, structural loading and commercial constraints.
What goes wrong in solar foundations
Solar foundations fail long before they are built.
These problems are predictable.
They are preventable.
- Ground Reports
- Bearing Capacity
- Drainage and Erosion
- Surveys
- Driving Refusal
- Installation
- Pile Length
- Erosion
Generic Ground Reports
A report can be technically correct and still be wrong for utility-scale solar. If it is not built around pile behavior, constructability and the applicable UK design standards, it can leave the project with assumptions that look acceptable on paper but create unnecessary risk on site.
Low Bearing Capacity
Weak ground zones can remain hidden until they start affecting performance or forcing redesign. Identifying them early allows foundation solutions to be adapted in time, before they become a construction or commercial problem.
Drainage and Erosion
Surface water is often treated as a site management issue, but on solar farms it can quickly become a foundation risk. Poorly understood drainage paths, erosion beneath array rows or flood exposure around pile locations can affect installation quality, long-term stability and future maintenance costs. Understanding water movement early helps protect both the design and the commercial performance of the asset.
Survey Accuracy
Accurate topographical survey data underpins design, setting out and earthworks. Poor topographic control can lead to wrong levels, unnecessary cut and fill, and cumulative installation errors that only become visible when they are expensive to correct.
Driving Refusal
Refusal and pile deviation should not be treated as site surprises. Anticipating where installation is likely to become difficult allows the contractor to plan the right plant, the right sequence and the right contingency before productivity is affected.
Installation Method
Direct ramming is often the most efficient solution, but it is not always the right one. Some sites require pre-drilling or alternative installation methods, and selecting the correct approach early helps reduce disruption, delay and reactive decisions during construction.
Pile Length
Getting pile length right is one of the clearest drivers of project value. Too little embedment can compromise long-term performance, while too much adds avoidable steel, installation effort and cost. The right answer is not a standard length, but the right length for the ground.
Drainage and Erosion
Surface water is often treated as a site management issue, but on solar farms it can quickly become a foundation risk. Poorly understood drainage paths, erosion beneath array rows or flood exposure around pile locations can affect installation quality, long-term stability and future maintenance costs. Understanding water movement early helps protect both the design and the commercial performance of the asset.
Ground Conditions in the UK Solar Market
Commercial solar projects in the UK face specific ground challenges:
Clay heavy soil
Soil data interpreted for solar foundations, not compliance boxes
Weather Risk
Better data means optimised pile lengths and validated depths
Project Scale
Early testing and validation catch problems before steel arrives
Steel exposure
Efficient design that reflects actual site conditions, not worst case
A generic report does not address these realities.
A solar focused investigation does.
Our Expertise
Dayla Geotechnical was built around utility-scale solar from day one. Our work is not adapted from generic geotechnical practice; it is designed around driven piles, constructibility and the risks that matter in the field

“A foundation can be cheap or expensive, simple or complex — but repairing it after installation is always the most costly option.”
David Jo Martinez
Founder, Dayla Geotechnical

“There will always be cheaper geotechnical reports. The real question is whether they reduce the risks that matter.”
Albert Fuentes Rodó
Founder, Dayla Geotechnical
Tendering for a solar project?
Early stage technical clarity reduces downstream risk. Simple.
If you are preparing a bid or reviewing ground investigation strategy, early input can prevent expensive redesign later.




